Funkwerk WI2040n Uživatelský manuál Strana 348
- Strana / 432
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Field Description
Password Enter the password as registered with the DynDNS provider.
Provider Select the DynDNS provider with which the above data is re-
gistered.
A choice of DynDNS providers is already available in the uncon-
figured state and their protocols are supported.
Other DynDNS providers can be configured in the Local Ser-
vices -> DynDNS Client-> DynDNS Providers menu.
The default value is 9-98 .
Enable update Select whether the DynDNS entry configured here is to be activ-
ated.
The function is activated by choosing 0#2.
The function is disabled by default.
The Advanced Settings menu consists of the following fields:
Fields in the menu Advanced Settings
Field Description
Mail Exchanger (MX) Enter the full host name of a mail server to which e-mails are to
be forwarded if the host currently configured is not to receive
mail.
Ask your provider about this forwarding service and make sure
e-mails can be received from the host entered as MX.
Wildcard Select whether the forwarding of all subdomains of the Host
Name are to be enabled for the current IP address of the Inter-
face (advanced name resolution).
The function is activated by choosing 0#2.
The function is disabled by default.
18.3.2 DynDNS Provider
In the Local Services -> DynDNS Client -> DynDNS Provider menu, a list of all con-
figured DynDNS providers is shown.
18 Local Services Funkwerk Enterprise Communications GmbH
336 bintec WLAN and Industrial WLAN
- Reference 1
- Legal Notice 2
- Table of Contents 11
- Chapter 1 Introduction 13
- 2 About this guide 17
- Chapter 3 Installation 18
- 3 Installation 19
- 3.2 Cleaning 24
- 3.3 Support information 25
- Chapter 4 Basic configuration 26
- 4.1.2 Software update 27
- 4.2 System requirements 28
- 4.3 Preparations 28
- 4.3.2 Configuring a PC 30
- 4.4 IP configuration 31
- 4 Basic configuration 33
- 4.5 Modify system password 34
- 4.7 Setting up a bridge link 35
- 4.8 Software Update 36
- Chapter 5 Reset 38
- Chapter 6 Technical data 40
- 6 Technical data 41
- 6.2 General Product Features 42
- 6.3 LEDs 51
- 6.4 Connectors 55
- 6.6 Pin Assignments 58
- 6.6.2 Serial interface 59
- 6.6.3 Socket for power supply 59
- 6.7 Frequencies and channels 60
- 6.8 WEEE information 61
- 7.1 Access Options 62
- 7.1.1.2 Telnet 63
- 7.1.1.3 SSH 63
- 7 Access and configuration 63
- 7.2 Logging in 67
- 7.3 Configuration options 68
- 7.3.1.2 Operating elements 71
- Fig. 30: Filter list 76
- 7.4 BOOTmonitor 84
- Chapter 8 Assistants 86
- Chapter 9 System Management 87
- 9.2 Global Settings 90
- 9.2.2 Passwords 92
- 9.2.3 Date and Time 94
- Time server 95
- 9.2.4 System Licences 98
- 9.2.4.1 Edit/New 99
- Routing versus bridging 101
- 9.3.1 Interfaces 103
- 9.3.1.1 <stax-x> Edit 104
- 9 System Management 105
- 9.4 Administrative Access 106
- 9.4.1 Access 107
- 9.4.2 SSH 108
- 9.4.3 SNMP 112
- 9.5 Remote Authentication 113
- RADIUS packets 114
- 9.5.1.1 Edit/New 115
- 9.5.2 TACACS+ 119
- 9.5.3 Options 122
- 9.6 Certificates 124
- 9.6.1.2 Request 126
- 9.6.1.3 Import 131
- 9.6.2 CRLs 133
- 9.6.3 Certificate Servers 134
- 10.1 Ethernet Ports 136
- 10 Physical Interfaces 137
- 10.2 Serial Port 138
- 10.3 Relay 142
- 10.3.1 Relay Configuration 143
- Chapter 11 LAN 144
- Example of subnets 145
- 11.1.1.1 Edit/New 145
- 11.2 VLAN 148
- Fig. 56: VLAN segmenting 149
- 11.2.1 VLANs 150
- 11.2.2 Port Configuration 151
- 11.2.3 Administration 152
- Chapter 12 Wireless LAN 153
- 12.1 WLAN 154
- 12 Wireless LAN 155
- 12.1.2 Virtual Service Sets 167
- 12.1.3 WDS Links 174
- 12.1.4 Client Link 177
- 12.1.4.2 Client Link Scan 179
- 12.1.5 Bridge Links 181
- Fig. 72: 1. Fresnel zone 184
- Fig. 73: Antenna connection 186
- 12.2 Administration 189
- 13.1 Wizard 191
- 13.1.3 Wireless Networks 192
- 13 Wireless LAN Controller 193
- 13.2 Controller Configuration 196
- 13.2.1 General 197
- 13.3 Slave AP Configuration 198
- 13.3.1 Slave Access Points 199
- 13.3.1.1 Edit 200
- 13.3.2 Radio Modules 201
- 13.3.2.1 Edit 202
- 13.3.3 Radio Profiles 204
- 13.3.3.1 Edit/New 205
- 13.3.4.1 Edit/New 211
- -> /New 212
- 13.4 Monitoring 216
- 13.4.1 Active Clients 217
- 13.5 Maintenance 218
- 13.5.1 Firmware Maintenance 219
- Chapter 14 Routing 221
- 14 Routing 223
- 14.1.2 Options 226
- 14.2 NAT 228
- 14.2.2 NAT Configuration 230
- 14.3 RIP 235
- 14.3.1.1 Edit 236
- 14.3.2 RIP Filter 238
- 14.3.2.1 New 239
- 14.3.3 RIP Options 240
- 14.4 Load Balancing 243
- 14.5 Multicast 245
- Address range for multicast 246
- Multicast basics 246
- 14.5.1 Forwarding 247
- 14.5.2 IGMP 248
- 14.5.2.1 New 249
- 14.5.3 Options 251
- 14.6 QoS 253
- 14.6.2 QoS Classification 256
- 14.6.3.1 New 259
- Chapter 15 WAN 265
- Default Route 266
- Activating NAT 266
- Connection Idle Timeout 266
- Authentication 266
- 15.1.1 PPPoE 267
- 15.1.2 PPTP 271
- 15.1.2.1 New 272
- 15.1.3 IP Pools 276
- 15.2 Real Time Jitter Control 277
- 15.2.1.1 New 278
- Field Description 279
- Chapter 16 VPN 280
- Peer Monitoring 281
- 16.1.1.1 New 281
- 16.1.2 Phase-1 Profiles 286
- 16.1.3 Phase-2 Profiles 293
- 16.1.3.1 New 294
- 16.1.4 XAUTH Profiles 297
- 16.1.4.1 New 298
- 16.1.5 IP Pools 300
- 16.1.6 Options 301
- 16.2 L2TP 304
- 16.2.2 Users 308
- 16.2.3 Options 314
- 16.3 GRE 315
- 16.3.1.1 New 316
- Chapter 17 Firewall 318
- IP Access Lists 319
- 17.1 Policies 319
- 17.1.1 Filter Rules 320
- 17.1.1.1 New 321
- 17 Firewall 321
- 17.1.2 QoS 323
- 17.1.3 Options 325
- 17.2 Interfaces 327
- 17.3 Addresses 328
- 17.3.2 Groups 329
- 17.4 Services 330
- 17.4.2 Groups 332
- Chapter 18 Local Services 334
- 18 Local Services 335
- 18.1.1 Global Settings 336
- 18.1.2 Static Hosts 339
- 18.1.3 Domain Forwarding 340
- 18.1.4 Cache 342
- 18.1.5 Statistics 344
- 18.2 HTTPS 345
- 18.3 DynDNS Client 346
- 18.3.1 DynDNS Update 347
- 18.3.2 DynDNS Provider 348
- 18.3.2.1 New 349
- 18.4 DHCP Server 350
- 18.4.1 DHCP Pool 351
- 18.4.2 IP/MAC Binding 353
- 18.4.3 DHCP Relay Settings 354
- 18.5 Scheduling 355
- 18.5.1 Schedule 356
- 18.5.2 Options 359
- 18.6 Surveillance 360
- 18.6.2 Interfaces 362
- 18.6.2.1 Edit/New 363
- 18.6.3 Temperature 364
- 18.6.3.1 New 365
- 18.6.4 Ping Generator 366
- 18.7 Funkwerk Discovery 367
- 18.7.1.1 Discover 368
- 18.8 Hotspot Gateway 371
- Requirements 372
- 18.8.1 Hotspot Gateway 373
- 18.8.1.1 Edit/New 374
- 18.8.1.2 Options 377
- Chapter 19 Maintenance 379
- 19.1.2 DNS Test 380
- 19.1.3 Traceroute Test 380
- 19.2.1 Options 381
- Operations 382
- Configuration file format 382
- 19 Maintenance 383
- 19.3 Reboot 386
- Chapter 20 External Reporting 387
- 20.1.1.1 New 388
- 20 External Reporting 389
- 20.2 IP Accounting 390
- 20.2.2 Options 391
- 20.3 E-mail Alert 392
- 20.3.2 E-mail Alert Recipient 394
- 20.4 SNMP 395
- 20.4.1 SNMP Trap Options 396
- 20.4.2 SNMP Trap Hosts 397
- 20.5 Activity Monitor 398
- 20.5.1 Options 399
- Chapter 21 Monitoring 401
- 21.2 IPSec 402
- 21 Monitoring 403
- 21.2.2 IPSec Statistics 404
- 21.3 Interfaces 406
- 21.4 WLAN 408
- 21.4.2 VSS 410
- 21.4.3 WDS 413
- WDS Link Details 414
- 21.4.4 Bridge Links 416
- Bridge link details 417
- 21.4.5 Client Links 418
- Client Link Details 419
- 21.5 Bridges 420
- 21.5.2 sta<x> 421
- 21.6 Hotspot Gateway 422
- 21.7 QoS 423
Související produkty a manuály pro Přístupové body WLAN Funkwerk WI2040n
(21 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce